Tag: Arkham Horror

Thou shalt not covet. When it comes to board game tables, I am almost willing to break a commandment. Very fancy board game tables have popped up at conventions, Kickstarter, and Etsy. I want it.

In most cases, a game table is just a dedicated surface for playing all manner of tabletop games. They usually include a spongy surface for being able to pick up cards and tokens easily, a wide frame to place your cards or area to write, and cup holders.

I decided to make my own gaming table.

The decision to make my own versus buying was helped by the fact that I had an attic filled with two-by-four pieces of wood and a giant 6’x3′ sheet of subflooring. The previous homeowner was in the middle of some unfinished woodworking projects. Since the sub-flooring sheet was 6’x3′, I made that my dimensions for the table. This also means that many gaming mats will fit perfectly. Gaming mats are like giant mouse pads with a print and made of a spongy backing.

Design

My design was simple. Build a 6’x’3 frame out of the two-by-fours. Add table legs. Put 6’x3′ subflooring panel on top. And, finally frame the whole thing to give the table a small ledge. I used 6″ oak panels from Lowes to build the ledge. The ledge is a separate piece so I can swap out the gaming mat if needed or clean up spills without ruining the whole thing.

Tools and Things

I didn’t have any woodworking tools. So, I assembled a short list of tools and things needed to build this table…

1. Snacks
2. Beverages
3. Friend with tools
   1. Miter saw
   2. Power drill and screwdriver
   3. Power sander
4. Screws
5. Corner brackets
6. Sandpaper
7. Pre-stain
8. Stain
9. Polycrylic sealer

To keep the costs down, I bribed a friend to help me. They get a lifetime pass for gaming action on a cool DIY game table… and, snacks and beverages. The main tool needed was a miter saw. This was used to make nice straight cuts. Other tools needed: power drill to drill holes for screws and a screwdriver to screw the screws into the holes.

Table Frame

I was only trying to make sure that the outside dimensions were 6’x3′. I made up the configuration on the spot.

Table Ledge

The ledge acts as a frame around the sub-flooring panel. This gives you a nice place to hold cards or write notes. I used corner brackets to square up the ledge and used the sub-flooring panel as my guide.

• 

• 

Table Assembly

The table is three separate parts: frame, subflooring surface, and ledge. Obligatory selfie. First Game = Arkham Horror: The Card Game.

• 

• 

• 

Finishing

For a while, I tried to talk myself out of sanding and staining the wood. The wood had sharp edges and rough spots. It took some convincing, but I decided to finish this off and it made a huge difference. The finishing process took way longer than the assembly.

My Process

• Sanding – so much sanding – this creates a lot of dust – wear a mask – be prepared to clean up dust for months – use 80 grit first, 120 second, and 220 third – be patient
• Pre-staining – apply pre-stain to the wood and let dry – this really helps with staining or so YouTube says
• Staining – apply stain within 2 hours of the pre-stain and repeat
• Sealing – use a water-based polyacrylic sealer to seal the ledge – this will help with spills and cup rings and protect the wood or so YouTube says – let dry for 30 minutes – lightly sand with 220 grit and repeat two more times – it’s worth doing this as many times as you can fit into a weekend

• 

• 

• 

• 

• 

Going Next Level

Deep-Cut Studio creates custom gaming mats for any size surface. I uploaded a custom piece of art to enhance my Arkham Horror: The Card Game campaign. Deep-Cut is based in England and it took less than two weeks to get my custom gaming mat. More on that on a later date.

• 

•